What to do about toilet overflow tube higher than allowed level …
网页The moogie on your fill valve suggests just that has been going on for quite some time. Oh wait, you just replaced the fill valve... Well, the new one shouldn't come this high. See also the legend on the back of the tank wall that says where fill level should be. That seems to agree with the instructions for the fill valve.
How do I fix a sticking toilet refill float?
网页2012年11月7日 · Flush the toilet to empty the tank (doesn't have to be completely empty, but you want some working space). Open the valve by lifting the float to the top position, pressing down on the black plastic cap that covers the valve, and giving it a 1/8 to 1/4 turn. You should then be able to lift the cap directly off.
Purpose of Fill Valve Tube Going into Overflow Drain
网页2014年6月29日 · 3. 1 water goes to the overflow tube thru the refill hose to refill the toilet after flushing , this is to keep sewer gas from entering the room and to prepare for the next flush. 2 At the same time water comes from a different part of the fill valve to refill the tank , all water flow stops when the float level is reached.
Toilet not flushing properly because flapper is closing too soon
网页2016年11月1日 · The flapper has to come up past vertical, so that it's out of the way for the full flush. Once the tank starts to fill again, the flapper will slam shut. If the chain is too long, it won't lift the flapper enough.
Cleaning an R&T A1250 toilet fill valve
网页2015年8月17日 · re-install the screen. to assure a good seal of the valve, clean the inside and outside of the toilet tank where the valve sits, wipe clean the outside of the valve rubber seal and the outside gasket removed in step 5. Re-install the valve, turn the water on, and check for leaks. If alls well, the toilet should now fill properly.
How to remove stuck locknut from porcelain toilet?
网页2020年9月9日 · That second piece is a cheap torque wrench allowing you to tighten it just so much before it slips but won't slip when loosening it. You have to hole it in place. – JACK. Sep 9, 2020 at 21:53. The nut must be pushed up to stay engaged while torque may be pushing it away due the nylon rounded edge. If you want to avoid damage to plastic ...
Why does this toilet fill valve leak around the top?
网页3. That's a fairly popular fill valve. To open it: Shutoff the water, you don't want a geyser. Lift the float to the top position. While holding up the float, push down on the top cap and twist the cap a quarter turn (I believe counter clockwise). The cap will then lift off and you can inspect and clean any parts.
Constantly running toilet with floatless fill valve
网页2017年9月9日 · A toilet with a floatless fill valve isn't fully closing and is filling past the overflow tube (blue circle in image): I have adjusted the adjustment knob (red circle) as much as possible to lower the water level. If observed closely in the image, the diagram at the right of the valve indicates to turn clockwise to "raise" or counterclockwise ...
plumbing - Toilet running constantly after replacing parts - Home ...
网页2018年1月9日 · Our toilet was running a bit, so we replaced the very old fill valve. All was great, but occasionally we were having some issues with the flapper chain getting caught up and causing the toilet to run A LOT, so I thought I would also replace the flush valve since that part was also really old. I bought an all-in-one repair kit (which for the ...
How to measure toilet flush valve? - Home Improvement Stack …
网页2015年2月25日 · 4. The image attached to this answer, shows what the flush valve is. It typically includes the overflow tube, but more specifically it's the flapper (or a device that controls the flow of water into the bowl). Measure the tank discharge (flush) tube (the hole the flush valve (flapper) covers), to determine the size flush valve you need.